Key benefits

• Around twice the notched impact strength of HT-PLA: 9.94 versus 4.94 kJ/m² in X–Y.
• Stronger layer bonding, with Z-axis tensile strength of 26.8 MPa.
• 3D printing speeds up to 300 mm/s with suitable hardware and settings.
• A standard brass nozzle is sufficient; no enclosure is required.
• Finished parts can be annealed to improve heat resistance under load.

HT-PLA Pro vs HT-PLA

Pro offers higher impact strength and improved strength between layers. This is useful for parts that are assembled, handled frequently or exposed to impacts. Compare it with Polymaker HT-PLA for your application.

These are typical laboratory values. Part orientation, geometry, walls, infill and print settings affect the strength of the finished part.

Heat resistance: Vicat and HDT

A Vicat softening temperature of 148.3°C does not mean a loaded part can operate continuously at that temperature. For parts exposed to both heat and mechanical load, use HDT — the heat deflection temperature at a specified load — as the more relevant reference.

Anneal at 100°C. Allow 30–60 minutes for walls under 4 mm, 1–2 hours at 6 mm, 2–4 hours at 8 mm and 3–6 hours at 10 mm. Use uniform heating, let the part cool inside the chamber and check its dimensions. Expected dimensional change is around 0.3–0.6%, so test a sample first for assemblies with tight tolerances.

3D printing settings

Start with a proven PLA profile and a short temperature, flow and layer-bonding test. Match the speed to your hotend flow and required finish. At 230°C the surface is semi-gloss. Around 210°C it becomes more matte, but strength may decrease.

Suitable applications

HT-PLA Pro is a practical choice for functional prototypes, brackets, clips, housings and workshop fixtures. For parts near a heat source, check the actual load and temperature against HDT. UV resistance is similar to ordinary PLA; ASA may be a better choice for prolonged exposure to direct sunlight.

Technical specifications and storage

Keep the spool in a sealed dry box with desiccant. If needed, dry at 60°C for 6 hours. Explore the other PLA filaments for 3D printing.

Polymaker HT-PLA Pro technical data sheet — PDF (EN)

Frequently asked questions

How does HT-PLA Pro differ from HT-PLA?

HT-PLA Pro has a notched Charpy impact strength of 9.94 kJ/m² in X–Y, compared with 4.94 kJ/m² for HT-PLA. Z-axis tensile strength is 26.8 versus 20.8 MPa. These are typical laboratory values; part orientation and print settings also affect performance.

Can HT-PLA Pro withstand 150°C under load?

The 148.3°C Vicat softening temperature is not a continuous service temperature under load. HDT at 0.45 MPa is 56.3°C as printed and 107.6°C after annealing. Select the material for the actual temperature, load and part geometry.

Which print settings should I use?

Start with a 230°C nozzle, a 25–65°C bed and the cooling fan on. The stated speed is up to 300 mm/s, subject to hotend flow and part geometry. Suggested direct-drive retraction is 1–3 mm at 20–40 mm/s.

Do I need a hardened nozzle or an enclosure?

No. Use a standard FDM/FFF 3D printer for 1.75 mm filament with a standard brass nozzle. An enclosure or heated chamber is not required.

How do I anneal HT-PLA Pro parts?

Anneal at 100°C. The detailed guidance specifies 30–60 minutes for walls under 4 mm; thicker parts need longer. Let the part cool inside the heating chamber and check its dimensions: a change of around 0.3–0.6% is possible.

How should I dry and store the filament?

If moisture has been absorbed, dry at 60°C for 6 hours. Store the spool in a sealed dry box with desiccant and check flow after drying or changing the print profile.

Is it suitable for permanent outdoor use?

UV resistance is similar to standard PLA. For prolonged direct sunlight, consider ASA according to the requirements of the application.

Which colours and spool size are offered?

This product is offered in Black and Grey, with a 1.75 mm diameter and 1 kg net filament weight. The finish is semi-gloss at 230°C. Printing at around 210°C gives a more matte finish but can reduce strength.

The post Polymaker HT-PLA Pro – 1.75 mm, 1 kg PLA Filament appeared first on 3DBGPRINT.

Direct Drive:

Recommended drying settings:

Standard drying:	100˚C for 10 hours
PolyDryer:	Level 3 in 18 hours (PolyDryer)
Hardening settings:	120˚ for 10 hours

The post Polymer Fiberon™ PET-CF17 (Copy) appeared first on 3DBGPRINT.

What is Polymaker Panchroma PLA Basic?

Polymaker Panchroma PLA Basic is a high-speed PLA filament for everyday 3D printing, developed to combine fast production and professional surface quality. The formula is optimized for FDM/FFF 3D printers and is suitable for both beginners and advanced users who want a reliable material for prototypes, models, decorative elements, and small series of products.

The filament is supplied as a standard spool with a diameter of 1.75 mm and a net weight of 1 kg, making it compatible with the vast majority of desktop and professional 3D printers on the market. The specially developed high-speed formula allows print speeds of up to 350 mm/s and a volumetric flow of up to 28 mm³/s without sacrificing detail and smoothness.

Technology and material quality

Panchroma PLA Basic uses a new generation of PLA with improved rheology and mechanical properties. Compared to standard PLA formulations, the material offers significantly higher plasticity – approximately 19% elongation at break versus approximately 6% for typical PLA, as well as nearly double the Charpy impact strength. This means that parts are less brittle and tend to bend before breaking, which is ideal for functional prototypes and parts that are handled frequently.

According to Panchroma’s official TDS, the density of PLA Basic (Regular) is approximately 1.30 g/cm³ at 23 °C, and the Vicat softening temperature is approximately 66 °C. This is typical for high-quality PLA – the material retains its shape under normal room conditions, but is not suitable for prolonged use in highly heated environments (e.g., in a car interior during summer).

The composition is optimized for stable extrusion and good shrinkage, resulting in uniform layers, clean edges, and minimal defects such as gaps or voids when settings are correct. In combination with adequate cooling, Panchroma PLA Basic performs excellently with bridges and overhangs typical of decorative models and functional geometries.

Productivity and workflow

The main advantage of Panchroma PLA Basic is its high working speed. The manufacturer states that the material supports printing speeds of up to 350 mm/s and a volumetric flow of up to 28 mm³/s on suitable high-speed printers. In practice, this allows for a significant reduction in printing time for large objects and series without losing detail.

The recommended parameters for extrusion are:

• Nozzle temperature: 190–230 °C (typical start 200–215 °C depending on printer and geometry)
• Heating plate temperature: 25–60 °C (often 40–50 °C for a good balance between adhesion and easy removal)
• Nozzle diameter: 0.4 mm as standard; smaller/larger nozzles are also available depending on the application
• Print speeds: 60–120 mm/s for “reliable” mode, up to 350 mm/s for high-speed profiles

The material behaves predictably with ready-made PLA profiles in popular slicers such as Bambu Studio, PrusaSlicer, Cura, and OrcaSlicer. In many cases, it is sufficient to use a standard PLA profile and set the speed and temperature within the recommended limits, but for maximum quality and consistency, additional fine tuning (flow, retraction, PA/pressure advance) is desirable.

For demanding models with many overhangs and detailed supports, Polymaker recommends using separate support materials such as PolySupport or soluble PolyDissolve S1, which ensure clean separation of the supports from the PLA part.

Compatibility and ecosystem

Panchroma PLA Basic is a filament with a diameter of 1.75 mm and is compatible with a wide range of FDM/FFF printers – from desktop models to larger professional machines. The low operating temperature and PLA base mean that no closed chamber or special hardware modifications are required.

The filament is marked as compatible with multifilament systems and AMS solutions (e.g., for automatic thread changing) thanks to the stable geometry of the spool and the uniform diameter. This makes it a suitable choice for complex projects with multiple materials or for automated production tasks.

In terms of software, Panchroma PLA Basic works with all standard 3D model formats – STL, 3MF, OBJ, etc. It is important that the model is correctly prepared in the slicer: correct wall thickness, layer height (e.g., 0.2 mm for a balance between speed and detail), and adequate layer cooling activated.

If you need detailed profiles, you can consult Polymaker’s official materials or use ready-made profiles for Panchroma/PolyLite PLA in your slicer, adapting them to your specific printer if necessary.

Reel design and ergonomics

Polymaker uses a well-thought-out spool design for Panchroma PLA Basic. The standard 1 kg spool has a rigid flange and a central sleeve that rotates smoothly on most filament reel holders. The holes in the body make it easy to secure the filament at the end of the print so that it does not unwind on its own during storage.

The label clearly states the type of material (PLA), diameter 1.75 mm, batch number, and recommended temperatures. This helps with traceability and repeatability in professional use—you can easily reproduce the parameters for a given customer or series.

The filament is delivered vacuum-packed with a silica gel packet, which keeps humidity low during transport and initial storage. For optimal performance, especially during longer prints and in more humid environments, it is recommended to store the spool in a box with desiccant or in a filament dryer.

Professional usage scenarios

• Functional prototypes and housings – thanks to its greater toughness and relatively good impact resistance, Panchroma PLA Basic is ideal for electronics housings, clips, holders, small mechanical parts, and demo prototypes that need to withstand repeated assembly and disassembly.
• Detailed miniatures and figurines – fine detail, clean surfaces, and minimal layer visibility enable printing of miniatures for board games, collectible figurines, or decorative statuettes, which can then be easily primed and painted.
• Cosplay accessories and props – the lightness of the material, combined with improved impact resistance, makes it suitable for helmets, weapons, armor, and other cosplay items that need to look good and withstand transport and wear.
• Educational and STEM projects – easy setup and good repeatability are ideal for schools, universities, and makerspaces where educational models, geometric shapes, mechanisms, and other demonstration objects are printed.
• Prototypes for product designers – fast printing and high-quality exterior surfaces enable rapid validation of shapes, ergonomics, and assemblies before moving on to more expensive technical materials.
• Small series of decorative products – thanks to its speed and stable color/quality consistency, Panchroma PLA Basic is suitable for the production of souvenirs, interior decorations, personalized gifts, and other small series.

Restrictions and best practices

Like any PLA, Panchroma PLA Basic has its limitations. Its softening temperature of around 60–66 °C means that the material is not suitable for applications in highly heated environments (e.g., in a car in the sun, near heaters, or outdoors in direct sunlight in high summer temperatures).

When printing on textured PEI beds, some users report strong adhesion. To avoid damaging the surface, it is good practice to:

• reduce the temperature of the bed to around 35–45 °C;
• use a separating layer (e.g., glue/tape) if adhesion is excessive;
• wait for the bed to cool completely before removing the parts.

For the best results:

• Store the filament in a dry place; if moisture is absorbed, it may be necessary to dry it at around 55 °C for 6 hours in a filament dryer.
• use smooth but not excessive acceleration and jerk settings at very high speeds;
• adjust the retraction to minimize threads and dots on the surfaces;
• If maximum strength is required, increase the temperature to the upper end of the recommended range and reduce the speed.

The material is PLA-based and, according to its specifications, is compatible with standard PLA settings. It should not be confused with Panchroma CoPE, which is a different material and is not recommended for combined printing with PLA in the same part.

The post Panchroma™ Basic PLA – Variations appeared first on 3DBGPRINT.

Colour, weight and diameter:

Description

Designed for high performance

Polymaker HT-PLA-GF combines excellent heat resistance with increased strength and durability. After thermal annealing, the material withstands temperatures up to 150°C, without sagging or deformation, making it ideal for functional parts subjected to heat stress.

Easy to print, extremely robust

Material prints smoothly with standard PLA settings and supports speeds up to 350 mm/s. Just load it up and get started – no additional configuration or specialized equipment required.

Reinforced with glass fibres. Stronger. Smarter.

HT-PLA-GF is glass fiber reinforced for increased rigidity and durability – ideal for demanding engineering applications.

Important: The material is abrasive. For optimum results, use a hardened steel or ruby nozzle.

Need even more heat resistance?

Anneal at 80-100°C for 30 minutes (100°C recommended) to raise the heat deflection temperature (HDT).

Available in 9 striking colours

The HT-PLA-GF combines ruggedness with style – for prints that don’t compromise on either performance or looks.

WARNING: WE RECOMMEND A HARDENED STEEL OR RUBY NOZZLE FOR BEST RESULTS

The post Polymaker™ HT-PLA-GF appeared first on 3DBGPRINT.

DESCRIPTION

PolyTerra PLA is a bioplastic-based 3D printing filament designed from the ground up to create the next generation of PLA, providing ease of use, print quality, speed and reliability.

This is a sustainable product, produced naturally and for every reel produced a tree is planted to return to the earth.

• Based on 0.4 mm nozzle and Simplify 3D v.3.1. Print conditions may vary between printers and nozzle diameters
• The mechanical properties of PolyTerra offer a wide range of possible applications because the material is stronger than normal PLA and still maintains good stiffness.

• Filament with reduced plastic content

The post PolyTerra™ Dual PLA appeared first on 3DBGPRINT.

Description

Polymide PA12-CF is PA12 filament (nylon) reinforced with carbon
fibers.
Due to the low moisture sensitivity of PA12, this
product is characterized by excellent mechanical and thermal properties.

Fibre adhesion technology

Fiber adhesion technology significantly improves the strength of the Z-
axis by designing the surface chemistry of the fibers to
achieve a strong fiber-matrix bond. Unlike
conventional fiber-reinforced filaments, which have a significant
reduction in Z-axis strength, PolyMide PA12-CF offers superior
interlayer adhesion compared to unreinforced PA12.

Deformation-free technology

Warp-Free technology enables the production of Polymaker nylon
filaments that can be printed with excellent
dimensional stability and virtually no warpage. This is achieved by
fine-tuning the microstructure and crystallization behavior of the
nylon, allowing the material to fully relieve internal
stresses before it hardens.

Annex

The combination of ease of printing with distortion-free
technology makes this product ideal for manufacturing
tools.

The post PolyMide PA12-CF / Black appeared first on 3DBGPRINT.

PolyMide is a family of nylon/polyamide based filaments. Manufactured with Polymaker’s Warp-Free technology, PolyMide filaments provide the engineering properties inherent in nylon and the ease of printing.

PolyMide PA6-CF is a carbon fiber reinforced PA6 (nylon 6) filament. The carbon fiber reinforcement provides significantly improved stiffness, strength and heat resistance with exceptional ply adhesion.

• Based on 0.4 mm nozzle and Simplify 3D v.4.0. Printing conditions may vary depending on different printers and nozzle diameters
  * We strongly recommend using a wear resistant nozzle

The post PolyMide™ PA6-CF / Black appeared first on 3DBGPRINT.

PolyLite is a family of 3D printing filaments made with the best raw materials to deliver exceptional quality and reliability. PolyLite covers the most popular 3D printing materials to meet your everyday needs in design and prototyping.

PolyLite ABS is made with a specialty bulk-polymerized ABS resin, which has significantly lower volatile content compared to traditional ABS resins. It delivers excellent printing quality with minimal odor during printing.

• Based on 0.4 mm nozzle and Simplify 3D v.3.1. Printing conditions may vary with different printers and nozzle diameters

The post PolyLite™ ABS appeared first on 3DBGPRINT.

PolyMide is a family of Nylon/polyamide based filaments. Produced with Polymaker’s Warp-Free technology, PolyMide filaments deliver engineering properties intrinsic to Nylon and ease of printing.

• Polymaker CoPA is a Copolymer Nylon filament for 3D printer that has excellent characteristics.The filament is heat resistant and you can make technical parts with it.
  For nylon, the filament is excellent for processing.
  CoPA Nylon is temperature resistant up to over 175°C.
  Polymaker Nylon has the resilience properties of Nylon 6/6 while retaining the high tensile strength, strength and resilience of Nylon 6.

The post PolyMide™ CoPA Nylon / Black appeared first on 3DBGPRINT.

Polymaker PC-ABS is a PC/ABS polymer blend that offers excellent strength and heat resistance, while exhibiting good surface finish and good compatibility with metal plating.

The industrial range of products provides engineering quality materials to unlock the use of 3D printing across multiple industries for new applications. Industrial products may require specific equipment and skills.

• Based on 0.4 mm nozzle and Simplify 3D v.4.0. Print conditions may vary depending on different printers and nozzle diameters

The post Polymaker™ PC-ABS appeared first on 3DBGPRINT.